(877) 636-4978

Fluorescent Labeling Hydrogels


Introduction

This protocol describes how to label HyStem®-C hydrogels either blue or green using Alexa Fluor® 350 C5-maleimide or Alexa Fluor 488 C5-maleimide use the following protocol. Note that any fluorescent label can be used so long as it is a C5-maleimide that is thiol reactive. This protocol will make 1.25 mL of HyStem-C that will be labeled with Alexa Fluor 350 C5-maleimide.

 

Required Materials
  • HyStem-C Hydrogels
  • Alexa Fluor 350 C5-maleimide
  • Alexa Fluor 488 C5-maleimide

 

Notes
  • Thiol-reactive Alexa Fluor 350 C5-maleimide and its conjugates exhibit an intense, blue fluorescence. Alexa Fluor 350 protein conjugates are optimally excited at ~346 nm and emit at a wavelength slightly shorter than that of AMCA or AMCA-X conjugates (~442 nm versus ~448 nm).
  • Thiol-reactive Alexa Fluor 488 C5 maleimide are its conjugates exhibit a bright, green fluorescence. Alexa Fluor 488 dye, which is spectrally similar to that of fluorescein, is pH-independent from pH 4 to 10.

Steps
  • 1. Remove Glycosil®, Gelin-S®, and Extralink® vials from the -20 °C freezer and heat them to 37 °C (~30 minutes).
     
  • 2. Remove the DG Water from the -20 °C freezer and thaw in a 37 °C water bath (~15 minutes).
     
  • 3. Prepare a stock solution of Alexa Fluor 350 C5-maleimide in DG Water by adding 0.025 mg to 10 μL of water.
    If you are using a different fluor, verify its solubility in water before proceeding. Make up only as much solution as you will use in one day since they are unstable and light sensitive. Read the manufacturer’s guidelines for making the stock solution to determine if additional steps are required to properly prepare the solution. The optimal pH for reaction of maleimides with thiols is ~7.0.
     
  • 4. Under aseptic conditions and using a syringe with the exact amount of liquid, add 1.0 mL of DG Water to the Glycosil vial. Repeat for the Gelin-S vial.
     
  • 5. Place both vials horizontally on a rocker at 37 °C (for maximum mixing).
    It will take <30 minutes for the solids to fully dissolve. Solutions will be clear and slightly viscous. Vigorous shaking will speed up dissolving time.
     
  • 6. Under aseptic conditions and using a syringe with the exact amount of liquid, add 0.5 mL of DG Water to the Extralink vial. Invert several times to dissolve.
     
  • 7. As soon as possible, but within four hours of making the solutions, mix equal volumes of Glycosil and Gelin-S. For a 1.25mL gel, combine 0.5mL Glycosil and 0.5mL Gelin-S. To mix, pipette back and forth or invert the vial.
     
  • 8. Protect the dye and hydrogel reaction from light.
     
  • 9. For 1.25 ml hydrogel, 0.025 mg dye will be needed.
     
  • 10. Add dye to the Glycosil/Gelin mixture. Allow reaction to proceed for two hours at room temperature.
     
  • 11. If encapsulating cells, add 100 μL of cells to 2.0 mL of Glycosil + Gelin-S. Pipette back and forth to mix.
     
  • 12. To form the hydrogel, add Extralink to the Glycosil + Gelin-S mix in a 1:4 volume ratio (0.25 mL Extralink to 1.0 mL Glycosil + Gelin-S). The total hydrogel volume with cells is 1.35 mL.
     
    Note: Gelation will occur within ~20 minutes.



Ordering Information

4 Item(s)

Set Ascending Direction
per page

Grid  List 

  • HyStem®-HP Hydrogels

    SKU: Multiple SKUS - View Products Options
    HyStem®-HP Hydrogels - The growth factor delivery matrix. Allows simultaneous growth factor, drug, and cell delivery in vivo less GF required in cell culture for cell signaling. Growth factors added to gel mixture ionically bind with heparin for a slow, more-controllable release. Components include Thiol-modified hyaluronan and heparin (Heprasil®), Thiol-reactive PEGDA crosslinker (Extralink®), Thiol-modified collagen (Gelin-S®), and Degassed, deionized water (DG Water). Learn More

    Starting at: $85.00

  • HyStem®-C Hydrogels

    SKU: Multiple SKUS - View Products Options
    HyStem®-C Hydrogels - The starter matrix. Good starter kit with incorporated collagen binding sites. Collagen provides general attachment protein for wide range of cells. Components include Thiol-modified hyaluronan (Gycosil®), Thiol-reactive PEGDA crosslinker (Extralink®), Thiol-modified collagen (Gelin-S®), and degassed, deionized water (DG Water). Learn More

    Starting at: $85.00

  • HyStem® Hydrogels

    SKU: Multiple SKUS - View Products Options
    HyStem® Hydrogels - The blank-slate matrix. Completely customizable and xeno-free. Components include Thiol-modified hyaluronan (Gycosil®), Thiol-reactive PEGDA crosslinker (Extralink®), and degassed, deionized water (DG Water). Learn More

    Starting at: $85.00

  • DG Water

    SKU: Multiple SKUS - View Products Options
    Degassed, deionized water at pH 5.0-8.0. Learn More

    Starting at: $4.50

4 Item(s)

Set Ascending Direction
per page

Grid  List